The engine of the automatic concrete loading mixer is the core engine of the mixer, and is the core component of whether the automatic concrete loading mixer can work smoothly. During the operation of the automatic concrete loading mixer, the high water temperature of the engine of the automatic concrete loading mixer is a frequent occurrence. Then, what should be done when the water temperature of the engine of the automatic concrete loading mixer is too high? The answers are as follows:
，打開發動機罩蓋，讓發動機怠速運轉，等待發動機溫度逐漸恢復正常。在發動機水溫恢復正常之后，將發動機熄火，然后再等待一段時間，直到發動機的水溫充分地下降了之后，再檢查發動機的冷卻水量。
First, open the engine cover, let the engine idle, and wait for the engine temperature to gradually return to normal. After the water temperature of the engine returns to normal, turn off the engine, and then wait for a period of time until the water temperature of the engine drops sufficiently, and then check the cooling water volume of the engine.
其次，如果混凝土自動上料攪拌車在普通公路上發動機出現了過熱，應該盡快地降低車速，把汽車駛到樹蔭下，或駛到相對比較涼快的地方，把汽車停下來，但這時候不要急于熄火。
Secondly, if the engine of the concrete automatic loading mixer is overheated on the ordinary road, the vehicle speed should be reduced as soon as possible, and the vehicle should be driven to the shade, or to a relatively cool place, and the vehicle should be stopped, but at this time, do not be in a hurry to stop the fire.
另外，另外，如果發現混凝土自動上料攪拌車發動機發熱現象，此時發動機的冷卻水量可能大都嚴重不足。按著規定量把冷卻水補足之后，再檢查一下冷卻系統，確認沒有其他故障之后，可以起動發動機，繼續行駛。也要檢查一下水箱百葉窗是不是被異物堵塞，風扇葉的工作情況，發動機皮帶是否打滑，發動機水泵工作情況等。
In addition, if the engine of the automatic concrete loading mixer is found to be hot, the cooling water of the engine may be mostly insufficient. After replenishing the cooling water according to the specified amount, check the cooling system again. After confirming that there are no other faults, start the engine and continue driving. Also check whether the water tank louver is blocked by foreign matters, the working condition of the fan blade, whether the engine belt slips, the working condition of the engine water pump, etc.
，混凝土自動上料攪拌車如果在高速公路上出現了發動機過熱，要立刻把暖風全部打開并打開車窗，由于有暖風幫助冷卻水散熱，能使冷卻水溫大幅度地下降。這樣可以讓您持續開車，就近找到高速公路的出口，將攪拌車駛到的場所停下來。接下來，只要按照上述的方法，使發動機的溫度降下來就行。注意，不要把攪拌車停在路邊，以免影響交通或被撞車，必須把攪拌車停在的場所。
In the end, the engine overheated on the highway. You have to open all the warm air and open the windows immediately. Then the car will be as hot as hell. Because there is warm air to help cooling water dissipate heat, the cooling water temperature can be greatly reduced. In this way, you can drive continuously, find the exit of the highway nearby, and drive the mixer to a safe place to stop. Next, just follow the above method to lower the engine temperature. Note that it is better not to park the mixer on the side of the road, so as not to affect the traffic or be hit. The mixer must be parked in a safe place.
以上是中科聚峰混凝土自動上料攪拌車發動機水溫過高的處理方法，希望今天小編的介紹能對大家有所幫助，以后使用時能更加得心順手。
The above is the treatment method for the excessive water temperature of the engine of Zhongke Jufeng concrete automatic loading mixer. I hope today's introduction of Xiaobian can help you and make you more comfortable when you use it in the future.
