全自動攪拌車軸承損壞了怎么處理？全自動攪拌車滑動軸承早期損壞比軸承燒毀要常見得多，因此預防滑動軸承早期損壞很重要。下面小編為您講解更為詳細的內容。

How to deal with the damaged bearings of the automatic mixer? The early damage of the sliding bearing of the automatic mixer is much more common than the bearing burning, so it is important to prevent the early damage of the sliding bearing. The following sections will explain more details for you.

滑動軸承的正確維護是減少軸承早期損壞的有效途徑，也是延長軸承壽命的可靠保證。因此，在發動機的日常維護和維修中，須注意軸承的合金表面、背面、端頭及邊緣棱角處的外觀形狀，

The correct maintenance of sliding bearing is an effective way to reduce the early damage of bearing, and also a reliable guarantee to extend the service life of bearing. Therefore, in the daily maintenance and repair of the engine, attention must be paid to the appearance of the alloy surface, back, end and edge corners of the bearing,

如有異?；虺霈F過半磨損的征兆，就要認真查明原因，并采取相應的措施，改善軸承的工作條件，重視對滑動軸承早期損壞的預防。

In case of any abnormality or signs of more than half wear, it is necessary to carefully find out the causes, take corresponding measures, improve the working conditions of bearings, and pay attention to the prevention of early damage of sliding bearings.

滑動軸承在氣缸壓力沖擊載荷的反復作用下，表面層發生塑性變形和冷作硬化，局部喪失變形能力，逐步形成條紋并不斷擴展，然后隨著磨屑的脫落，在受載表面層形成凹穴。一般軸瓦發生穴蝕時，是先出現凹坑。

Under the repeated action of the cylinder pressure impact load, the surface layer of the sliding bearing undergoes plastic deformation and cold work hardening, loses the deformation ability locally, gradually forms stripes and continues to expand, and then forms cavities on the loaded surface layer as the wear debris falls off. In general, when cavitation occurs on the bearing bush, the pit appears first.

然后這種凹坑逐步擴大并引起合金層界面的開裂，裂紋沿著界面的平行方向擴展，直到剝落為止。

Then the pits gradually expand and cause the alloy layer interface to crack, and the cracks extend along the parallel direction of the interface until peeling off.

滑動軸承穴蝕的主要原因是，由于油槽和油孔等結構要素的橫斷面突然改變引起油流強烈紊亂，在油流紊亂的真空區形成氣泡，隨后由于壓力升高，氣泡潰滅而產生穴蝕。

The main reason for cavitation of sliding bearing is that the sudden change of cross section of structural elements such as oil groove and oil hole causes a strong disorder of oil flow, forming bubbles in the vacuum area where the oil flow is disordered, and then cavitation occurs due to bubble collapse due to pressure rise.

全自動攪拌車軸承損壞了怎么處理？以上就是問題的相關解答了，所以說要求你在平日使用中多檢查固定維護保養，延長其壽命不是問題。關注我們http://www.jqeq.cn，了解更多問題！

How to deal with the damaged bearings of the automatic mixer? The above is the relevant answer to the question, so you are required to check and maintain the fixed parts more frequently in daily use, so it is not a problem to extend their service life. Follow us http://www.jqeq.cn , learn more!